Mettler Toledo M400 Especificações Página 70
- Página / 88
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter Multiparameter M400 70
© 11 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M400
Printed in Switzerland 52 121 378
Definition:
Adjustment: The calibration procedure is completed and the calibration values are taken over
and used for the measurement (Act) and stated in Cal-1. The current values from Act will move
to Cal-2.
Calibration: The calibration procedure is completed, but the calibration values will not be
overtaken and the measurement continuous with the last valid adjustment dataset (Act). The
dataset will be stored under Cal-1.
The calibration history is used for the estimation of the lifetime indicator for ISM sensors.
Sensor Monitoring
The sensor monitoring shows the different diagnostics functions available for each ISM sensor.
The following information is available:
Lifetime indicator: Shows an estimation of the remaining lifetime to ensure a reliable measure-
ment. The lifetime is indicated in days (d) and percentage (%). For a description of the Lifetime
indicator, please see section 8.6 ISM Setup. For Oxygen sensors, the lifetime indicator is
related to the inner-body of the sensor or the OptoCap for optical sensors. If you want to bring
the bar indicator on the screen, see chapter 8.7.5 to activate ISM functions.
Adaptive Cal Timer: This timer shows a Adaptive Cal Timer, when the next calibration should be
performed to keep the best possible measurement performance. The Adaptive Cal Timer is
indicated in days (d) and percentage (%). For a description of the Adaptive Cal Timer, please
see section 8.6 ISM Setup.
Time to Maintenance: This timer shows a Time to Maintenance, when the next cleaning cycle
should be performed to keep the best possible measurement performance. The Time to
Maintenance is indicated in days (d) and percentage (%). For a description of the Time to
Maintenance, please see section 8.6 ISM Setup. For oxygen sensors, the Time to Maintenance
indicates a maintenance cycle for the membrane and electrolyte.
Max. Temperature
The maximum temperature shows the maximum temperature that this sensor has ever seen,
together with a time stamp of this maximum. This value is stored on the sensor and cannot be
changed. During autoclaving the Max temperature is not recorded.
Max. Temperature
Tmax XXX°C YY / MM / DD
CIP Cycles
Shows the amount of CIP cycles that the sensor has been exposed to. For a description of the
CIP Cycle indicator, please see section 8.6 ISM Setup
CIP Cycles xxx of xxx
SIP Cycles
Shows the amount of SIP cycles that the sensor has been exposed to. For a description of the
SIP Cycle indicator, please see section 8.6 ISM Setup
SIP Cycles xxx of xxx
Autoclaving Cycles
Shows the amount of Autoclaving cycles that the sensor has been exposed to. For a description
of the AutoClave Cycle indicator, please see section 8.6 ISM Setup
Autoclaving Cycles xxx of xxx
- Operation Manual 1
- Multiparameter 1
- Transmitter M400 1
- 1 Introduction 7
- 2 Safety instructions 7
- WARNINGS: 8
- 3 Unit overview 9
- 3.2.1 Menu Structure 10
- 3.2.2 Navigation keys 10
- ↑ in Display 11
- 3.2.6 ”Save changes” dialog 12
- 3.2.7 Security Passwords 12
- 3.3 Display 12
- 4 Installation instruction 13
- 4.1.2 Installation procedure 14
- �40 ... �60 mm 15
- �1.57... �2.36" 15
- 4.2.1 Housing (wall mount) 16
- 4.3 Connector PIN definition 17
- 4.3.1 TB1 and TB2 17
- 4.4.2 AK9 Cable Assignment 20
- A B C D E F S 21
- 4.4.4 VP Cable Assignment 22
- 4.4.5.1 Example 1 23
- 4.4.5.2 Example 2 24
- 4.4.5.3 Example 3 25
- 4.4.5.4 Example 4 26
- A B C D E F 29
- 6 Quick Setup 31
- 7 Sensor Calibration 32
- 7.3 Oxygen Calibration 33
- 7.3.3 Process Calibration 34
- 7.4 pH Calibration 35
- 7.4.1 One point calibration 35
- 7.4.2 Two point calibration 36
- 7.4.3 Process calibration 36
- 7.4.4 mV calibration 36
- 7.7 Sensor Verification 38
- 8 Configuration 39
- 8.2.3 pH / O 40
- Parameter related settings 40
- 8.2.3.2 pH Parameters 41
- 8.2.4 Set Averaging 42
- 8.3 Analog Outputs 43
- 8.4 Setpoints 44
- 8.5 Alarm / Clean 45
- 8.5.1 Alarm 45
- 8.5.2 Clean 46
- 8.6.1 Sensor Monitoring 46
- 8.6.2 CIP Cycle Limit 47
- 8.6.3 SIP Cycle Limit 48
- 8.7 Display 49
- 8.7.1 Measurement 49
- 8.7.2 Resolution 50
- 8.7.3 Backlight 50
- 8.7.4 Name 50
- 8.8 Hold Analog Outputs 51
- 9 System 52
- 9.3 Passwords 53
- 9.3.1 Changing Passwords 53
- 9.4 Set / Clear Lockout 54
- 9.5 Reset 54
- 9.5.1 Reset System 54
- 9.6 Set Date & Time 55
- 10 PID Setup 56
- 10.1 Enter PID Setup 57
- 10.2 PID Auto / Manual 57
- 10.3 Mode 58
- 10.3.1 PID Mode 58
- 10.4 Tune Parameters 59
- 10.4.3 Proportional Limits 60
- 10.4.4 Corner Points 60
- 10.5 PID Display 60
- 11 Service 61
- 11.1.3 Display 62
- 11.1.4 Keypad 62
- 11.1.5 Memory 62
- 11.1.6 Set Relay 62
- 11.1.7 Read Relays 63
- 11.1.8 Set Analog Outputs 63
- 11.1.9 Read Analog Outputs 63
- 11.2 Calibrate 64
- 11.2.1.1 Temperature 64
- 11.2.1.2 Current 65
- 11.2.1.3 Voltage 65
- 11.2.1.4 Rg Diagnostic 66
- 11.2.1.5 Rr Diagnostics 66
- 11.2.2 Calibrate Analog 67
- 11.2.3 Calibrate Unlock 67
- 11.3 Tech Service 67
- 12 Info 68
- 13 Maintenance 71
- 14 Troubleshooting 71
- 14.1 Changing the Fuse 72
- 16 Specifications 75
- 17 Default tables 77
- 17.2 M400 78
- 17.3 Error messages 80
- 18 Warranty 81
- 19 Buffer tables 82
- 19.3 NIST Technical Buffers 83
- 19.5 Hach buffers 84
- 19.6 Ciba (94) buffers 84
- 19.8 WTW buffers 85
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M400
(70 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais