Mettler Toledo M400 Especificações Página 64
- Página / 88
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter Multiparameter M400 64
© 11 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M400
Printed in Switzerland 52 121 378
11.2 Calibrate
(PATH: Menu / Service / Calibrate)
This menu has the options to calibrate the transmitter and the analog outputs and also allows
the unlocking of calibration functionality.
11.2.1 Calibrate Meter (only for channel A)
The M400 transmitter is factory calibrated within specifications. It is not normally necessary
to perform meter re-calibration unless extreme conditions cause an out of spec operation
shown by Calibration Verification. Periodic verification / re-calibration may also be necessary
to meet Q.A. requirements. Meter calibration can be selected as Current (used for most dissolved
oxyge, Voltage, Rg Diagnostic, Rr Diagnostic (used for pH), and Temperature (used for all
measurements).
11.2.1.1 Temperature
Temperature is performed as a three point calibration. The table above shows the resistance
values of these three points.
Navigate to the Calibrate Meter screen and choose Temperature calibration for Channel A.
Press [ENTER] to begin temperature calibration process
The first text line will ask for the Point 1 temperature resistance value (this will correspond to
Temperature 1 value shown on the Calibration Module Accessory). The second text line will
show the measured resistance value. When the value stabilizes, press [ENTER] to perform
calibration.
The transmitter screen will then prompt the user to enter the value for Point 2, and T2 will
display the measured resistance value. When this value stabilizes, press [ENTER] to calibrate
this range.
Repeat these steps for Point 3.
Press [ENTER] to bring up a confirmation screen. Select Yes to save the calibration values and
the successful Calibration is confirmed on the display.
The transmitter will return to the Measurement mode in approximately 5 seconds.
- Operation Manual 1
- Multiparameter 1
- Transmitter M400 1
- 1 Introduction 7
- 2 Safety instructions 7
- WARNINGS: 8
- 3 Unit overview 9
- 3.2.1 Menu Structure 10
- 3.2.2 Navigation keys 10
- ↑ in Display 11
- 3.2.6 ”Save changes” dialog 12
- 3.2.7 Security Passwords 12
- 3.3 Display 12
- 4 Installation instruction 13
- 4.1.2 Installation procedure 14
- �40 ... �60 mm 15
- �1.57... �2.36" 15
- 4.2.1 Housing (wall mount) 16
- 4.3 Connector PIN definition 17
- 4.3.1 TB1 and TB2 17
- 4.4.2 AK9 Cable Assignment 20
- A B C D E F S 21
- 4.4.4 VP Cable Assignment 22
- 4.4.5.1 Example 1 23
- 4.4.5.2 Example 2 24
- 4.4.5.3 Example 3 25
- 4.4.5.4 Example 4 26
- A B C D E F 29
- 6 Quick Setup 31
- 7 Sensor Calibration 32
- 7.3 Oxygen Calibration 33
- 7.3.3 Process Calibration 34
- 7.4 pH Calibration 35
- 7.4.1 One point calibration 35
- 7.4.2 Two point calibration 36
- 7.4.3 Process calibration 36
- 7.4.4 mV calibration 36
- 7.7 Sensor Verification 38
- 8 Configuration 39
- 8.2.3 pH / O 40
- Parameter related settings 40
- 8.2.3.2 pH Parameters 41
- 8.2.4 Set Averaging 42
- 8.3 Analog Outputs 43
- 8.4 Setpoints 44
- 8.5 Alarm / Clean 45
- 8.5.1 Alarm 45
- 8.5.2 Clean 46
- 8.6.1 Sensor Monitoring 46
- 8.6.2 CIP Cycle Limit 47
- 8.6.3 SIP Cycle Limit 48
- 8.7 Display 49
- 8.7.1 Measurement 49
- 8.7.2 Resolution 50
- 8.7.3 Backlight 50
- 8.7.4 Name 50
- 8.8 Hold Analog Outputs 51
- 9 System 52
- 9.3 Passwords 53
- 9.3.1 Changing Passwords 53
- 9.4 Set / Clear Lockout 54
- 9.5 Reset 54
- 9.5.1 Reset System 54
- 9.6 Set Date & Time 55
- 10 PID Setup 56
- 10.1 Enter PID Setup 57
- 10.2 PID Auto / Manual 57
- 10.3 Mode 58
- 10.3.1 PID Mode 58
- 10.4 Tune Parameters 59
- 10.4.3 Proportional Limits 60
- 10.4.4 Corner Points 60
- 10.5 PID Display 60
- 11 Service 61
- 11.1.3 Display 62
- 11.1.4 Keypad 62
- 11.1.5 Memory 62
- 11.1.6 Set Relay 62
- 11.1.7 Read Relays 63
- 11.1.8 Set Analog Outputs 63
- 11.1.9 Read Analog Outputs 63
- 11.2 Calibrate 64
- 11.2.1.1 Temperature 64
- 11.2.1.2 Current 65
- 11.2.1.3 Voltage 65
- 11.2.1.4 Rg Diagnostic 66
- 11.2.1.5 Rr Diagnostics 66
- 11.2.2 Calibrate Analog 67
- 11.2.3 Calibrate Unlock 67
- 11.3 Tech Service 67
- 12 Info 68
- 13 Maintenance 71
- 14 Troubleshooting 71
- 14.1 Changing the Fuse 72
- 16 Specifications 75
- 17 Default tables 77
- 17.2 M400 78
- 17.3 Error messages 80
- 18 Warranty 81
- 19 Buffer tables 82
- 19.3 NIST Technical Buffers 83
- 19.5 Hach buffers 84
- 19.6 Ciba (94) buffers 84
- 19.8 WTW buffers 85
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M400
(70 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais