Mettler Toledo M400 Especificações Página 48
- Página / 88
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter Multiparameter M400 48
© 11 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M400
Printed in Switzerland 52 121 378
CIP characteristics: CIP Cycles will be automatically recognized by the sensor. Since CIP cycles
will vary in intensity (duration and temperature) for each application the algorithm of the counter
recognizes an increase of the measurement temperature above a certain level (70 °C for CIP). If
the temperature does not decrease below (60 °C for CIP) within the next 5 minutes after the first
temperature was reached, the counter in question will be incremented by one and also locked
for the next two hours. In the case the CIP would last longer than two hours the counter would
be incremented by one once more.
8.6.3 SIP Cycle Limit
The SIP cycle limit counts the number of SIP cycles if the limit (user defined) is reached, an
alarm can be indicated and set to a certain output relays. The following options are possible:
SIP Max 000
Alarm YES / NO R# choose relay
If the Max setting is on 000, the counter functionality is turned off. The alarm will be reseted after
exchanging the sensor. For oxygen sensors, the counter can be reseted in the ISM Setup menu
(menu Configure).
SIP characteristics: SIP Cycles will be automatically recognized by the sensor. Since SIP cycles
will vary in intensity (duration and temperature) for each application the algorithm of the counter
recognizes an increase of the measurement temperature above a certain level (110 °C for SIP).
If the temperature does not decrease below (100 °C for SIP) within the next 5 minutes after the
first temperature was reached, the counter in question will be incremented by one and also
locked for the next two hours. In the case the SIP would last longer than two hours the counter
would be incremented by one once more.
8.6.4 Autoclaving Cycle Limit
The Autoclaving cycle limit counts the number of Autoclaving cycles if the limit (user defined) is
reached, an alarm can be indicated and set to a certain output relays. The following options are
possible:
Autoclave Max 000
Alarm YES / NO R# choose relay
If the Max setting is on 000, the counter functionality is turned off. The alarm will be reseted after
exchanging the sensor. For oxygen sensors, the counter can be reseted in the ISM Setup menu
(menu Configure).
Autoclave characteristics: Since during the Autoclaving cycle the sensor is not connected to the
transmitter, you will be asked after every Sensor connection, whether the sensor was autoclaved
or not. According to your selection, the counter will be incremented or not.
- Operation Manual 1
- Multiparameter 1
- Transmitter M400 1
- 1 Introduction 7
- 2 Safety instructions 7
- WARNINGS: 8
- 3 Unit overview 9
- 3.2.1 Menu Structure 10
- 3.2.2 Navigation keys 10
- ↑ in Display 11
- 3.2.6 ”Save changes” dialog 12
- 3.2.7 Security Passwords 12
- 3.3 Display 12
- 4 Installation instruction 13
- 4.1.2 Installation procedure 14
- �40 ... �60 mm 15
- �1.57... �2.36" 15
- 4.2.1 Housing (wall mount) 16
- 4.3 Connector PIN definition 17
- 4.3.1 TB1 and TB2 17
- 4.4.2 AK9 Cable Assignment 20
- A B C D E F S 21
- 4.4.4 VP Cable Assignment 22
- 4.4.5.1 Example 1 23
- 4.4.5.2 Example 2 24
- 4.4.5.3 Example 3 25
- 4.4.5.4 Example 4 26
- A B C D E F 29
- 6 Quick Setup 31
- 7 Sensor Calibration 32
- 7.3 Oxygen Calibration 33
- 7.3.3 Process Calibration 34
- 7.4 pH Calibration 35
- 7.4.1 One point calibration 35
- 7.4.2 Two point calibration 36
- 7.4.3 Process calibration 36
- 7.4.4 mV calibration 36
- 7.7 Sensor Verification 38
- 8 Configuration 39
- 8.2.3 pH / O 40
- Parameter related settings 40
- 8.2.3.2 pH Parameters 41
- 8.2.4 Set Averaging 42
- 8.3 Analog Outputs 43
- 8.4 Setpoints 44
- 8.5 Alarm / Clean 45
- 8.5.1 Alarm 45
- 8.5.2 Clean 46
- 8.6.1 Sensor Monitoring 46
- 8.6.2 CIP Cycle Limit 47
- 8.6.3 SIP Cycle Limit 48
- 8.7 Display 49
- 8.7.1 Measurement 49
- 8.7.2 Resolution 50
- 8.7.3 Backlight 50
- 8.7.4 Name 50
- 8.8 Hold Analog Outputs 51
- 9 System 52
- 9.3 Passwords 53
- 9.3.1 Changing Passwords 53
- 9.4 Set / Clear Lockout 54
- 9.5 Reset 54
- 9.5.1 Reset System 54
- 9.6 Set Date & Time 55
- 10 PID Setup 56
- 10.1 Enter PID Setup 57
- 10.2 PID Auto / Manual 57
- 10.3 Mode 58
- 10.3.1 PID Mode 58
- 10.4 Tune Parameters 59
- 10.4.3 Proportional Limits 60
- 10.4.4 Corner Points 60
- 10.5 PID Display 60
- 11 Service 61
- 11.1.3 Display 62
- 11.1.4 Keypad 62
- 11.1.5 Memory 62
- 11.1.6 Set Relay 62
- 11.1.7 Read Relays 63
- 11.1.8 Set Analog Outputs 63
- 11.1.9 Read Analog Outputs 63
- 11.2 Calibrate 64
- 11.2.1.1 Temperature 64
- 11.2.1.2 Current 65
- 11.2.1.3 Voltage 65
- 11.2.1.4 Rg Diagnostic 66
- 11.2.1.5 Rr Diagnostics 66
- 11.2.2 Calibrate Analog 67
- 11.2.3 Calibrate Unlock 67
- 11.3 Tech Service 67
- 12 Info 68
- 13 Maintenance 71
- 14 Troubleshooting 71
- 14.1 Changing the Fuse 72
- 16 Specifications 75
- 17 Default tables 77
- 17.2 M400 78
- 17.3 Error messages 80
- 18 Warranty 81
- 19 Buffer tables 82
- 19.3 NIST Technical Buffers 83
- 19.5 Hach buffers 84
- 19.6 Ciba (94) buffers 84
- 19.8 WTW buffers 85
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M400
(70 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais