Mettler Toledo M400 Especificações Página 51
- Página / 88
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter Multiparameter M400 51
© 11 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M400
Printed in Switzerland 52 121 378
8.7.5 ISM Sensor Monitoring
(available when ISM sensor connected)
The sensor monitoring allows you to display the sensor monitoring details on line 3 and 4 in the
display. The following options are possible:
Line 3 Off / Time Indicator / Time to Maint / Adapt Cal Timer
Line 4 Off / Time Indicator / Time to Maint / Adapt Cal Timer
8.8 Hold Analog Outputs
(PATH: Menu / Configure / Hold Outputs)
Enter configuration mode as described in Section 8.1.
The ”Hold outputs” function applies during the calibration process. If set ”Hold outputs” to Yes,
during calibration process the analog output, the output relay and USB ouptut will be at hold
state. The hold state depends on the setting. For the possible hold settings, see the list below.
The following options are possible:
Hold Outputs? Yes / No
The ”DigitalIn” function applies all the time. As soon as a signal is active on the digital input
the transmitter goes to hold mode and the values on the analog output, the output relays and the
USB output will be at hold state.
DigitalIn1 / 2 State = On / Low / High
C
NOTE: DigitalIn1 is to hold channel A (conventional sensor)
DigitalIn2 is to hold channel B (ISM sensor)
Possible Hold states:
Output relays: On / Off (Configuration / Set point)
Analog Output: Last / Fixed (Configuration / Analog output)
USB: Last / Off (System / USB)
PID relay Last / Off (PID setup/Mode)
PID analog Last / Off (PID setup/Mode)
- Operation Manual 1
- Multiparameter 1
- Transmitter M400 1
- 1 Introduction 7
- 2 Safety instructions 7
- WARNINGS: 8
- 3 Unit overview 9
- 3.2.1 Menu Structure 10
- 3.2.2 Navigation keys 10
- ↑ in Display 11
- 3.2.6 ”Save changes” dialog 12
- 3.2.7 Security Passwords 12
- 3.3 Display 12
- 4 Installation instruction 13
- 4.1.2 Installation procedure 14
- �40 ... �60 mm 15
- �1.57... �2.36" 15
- 4.2.1 Housing (wall mount) 16
- 4.3 Connector PIN definition 17
- 4.3.1 TB1 and TB2 17
- 4.4.2 AK9 Cable Assignment 20
- A B C D E F S 21
- 4.4.4 VP Cable Assignment 22
- 4.4.5.1 Example 1 23
- 4.4.5.2 Example 2 24
- 4.4.5.3 Example 3 25
- 4.4.5.4 Example 4 26
- A B C D E F 29
- 6 Quick Setup 31
- 7 Sensor Calibration 32
- 7.3 Oxygen Calibration 33
- 7.3.3 Process Calibration 34
- 7.4 pH Calibration 35
- 7.4.1 One point calibration 35
- 7.4.2 Two point calibration 36
- 7.4.3 Process calibration 36
- 7.4.4 mV calibration 36
- 7.7 Sensor Verification 38
- 8 Configuration 39
- 8.2.3 pH / O 40
- Parameter related settings 40
- 8.2.3.2 pH Parameters 41
- 8.2.4 Set Averaging 42
- 8.3 Analog Outputs 43
- 8.4 Setpoints 44
- 8.5 Alarm / Clean 45
- 8.5.1 Alarm 45
- 8.5.2 Clean 46
- 8.6.1 Sensor Monitoring 46
- 8.6.2 CIP Cycle Limit 47
- 8.6.3 SIP Cycle Limit 48
- 8.7 Display 49
- 8.7.1 Measurement 49
- 8.7.2 Resolution 50
- 8.7.3 Backlight 50
- 8.7.4 Name 50
- 8.8 Hold Analog Outputs 51
- 9 System 52
- 9.3 Passwords 53
- 9.3.1 Changing Passwords 53
- 9.4 Set / Clear Lockout 54
- 9.5 Reset 54
- 9.5.1 Reset System 54
- 9.6 Set Date & Time 55
- 10 PID Setup 56
- 10.1 Enter PID Setup 57
- 10.2 PID Auto / Manual 57
- 10.3 Mode 58
- 10.3.1 PID Mode 58
- 10.4 Tune Parameters 59
- 10.4.3 Proportional Limits 60
- 10.4.4 Corner Points 60
- 10.5 PID Display 60
- 11 Service 61
- 11.1.3 Display 62
- 11.1.4 Keypad 62
- 11.1.5 Memory 62
- 11.1.6 Set Relay 62
- 11.1.7 Read Relays 63
- 11.1.8 Set Analog Outputs 63
- 11.1.9 Read Analog Outputs 63
- 11.2 Calibrate 64
- 11.2.1.1 Temperature 64
- 11.2.1.2 Current 65
- 11.2.1.3 Voltage 65
- 11.2.1.4 Rg Diagnostic 66
- 11.2.1.5 Rr Diagnostics 66
- 11.2.2 Calibrate Analog 67
- 11.2.3 Calibrate Unlock 67
- 11.3 Tech Service 67
- 12 Info 68
- 13 Maintenance 71
- 14 Troubleshooting 71
- 14.1 Changing the Fuse 72
- 16 Specifications 75
- 17 Default tables 77
- 17.2 M400 78
- 17.3 Error messages 80
- 18 Warranty 81
- 19 Buffer tables 82
- 19.3 NIST Technical Buffers 83
- 19.5 Hach buffers 84
- 19.6 Ciba (94) buffers 84
- 19.8 WTW buffers 85
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M400
(70 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais