Mettler Toledo M400/2(X)H Especificações Página 63
- Página / 111
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter M400/2(X)H, M400G/2XH 63
© 03 / 2014 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter M400/2(X)H, M400G/2XH
Printed in Switzerland 30 031 683
The Autoclaving Cycle Limit counts the number of autoclaving cycles. If the limit (user defined)
is reached, an alarm can be indicated and set to a certain output OC. The following options are
possible:
Autoclave Max 000
Alarm YES / NO R# choose OC
If the Max setting is on 000, the counter functionality is turned off. The alarm will be reset after
exchanging the sensor. For oxygen sensors, the counter can also be reset manually (see
chapter “Reset ISM counter/timer”).
Autoclave characteristics: Since during the autoclaving cycle the sensor is not connected to the
transmitter, you will be asked after every sensor connection, whether the sensor was autoclaved
or not. According to your selection, the counter will be incremented or not.
Pressing the [ENTER] key will bring up the Save Changes dialog. Selecting No will discard the
entered values, selecting Yes will make the entered values the current ones.
8.6.5 Reset ISM counter / timer
This menu allows resetting counter and timer functions which cannot be reseted automatically.
The adaptive calibration timer will be reseted after a successful adjustment or calibration.
Navigate to the menu “Reset ISM Counter/Timer” by using the and . keys and press
[ENTER].
If an pH sensor or amperometric oxygen sensor is connected, the menu for resetting the Time To
Maintenance is displayed. Time To Maintenance needs to be reset after the following operations.
pH sensors: manual maintenance cycle on the sensor.
oxygen sensor: manual maintenance cycle on the sensor or exchanging of the inner-body or
membrane of the sensor
[Press ENTER]
If an oxygen sensor is connected, the menu for resetting the CIP and SIP counter is displayed.
These counters should be reset after the following operations.
amperometric sensor: exchanging of the inner-body of the sensor.
[Press ENTER]
8.6.6 DLI stress adjustment (only for pH ISM sensors)
Through this menu the calculation of the diagnostic data DLI, TTM and ACT can be adapted to
application requirements and/or experience.
h
NOTE: The function is only available for pH ISM sensors with corresponding firmware versions.
- Operation Manual 1
- Multi-parameter 1
- 1 Introduction 9
- 2 Safety instructions 10
- 3 Unit overview 14
- 3.2.1 Menu Structure 15
- 3.2.2 Navigation keys 15
- 3.2.6 ”Save changes” dialog 17
- 3.2.7 Security Passwords 17
- 3.2.8 Display 17
- 4 Installation instruction 18
- 4.1.2 Installation procedure 19
- (+ 0,5 mm/– 0,0 mm) 20
- (+ 0.02"/– 0.00") 20
- 4.2.1 Housing (wall mount) 21
- 4.3 Connector PIN denition 22
- 4.3.3 Analog Sensors 23
- InPro 3250i/SG/120 25
- Art.-Nr. 52 005 373 25
- 4.5.2.1 Example 1 27
- 4.5.2.2 Example 2 28
- 4.5.2.3 Example 3 29
- 4.5.2.4 Example 4 30
- 6 Quick Setup 34
- 7 Sensor Calibration 35
- (four electrode sensors only) 37
- 7.2.3 Process Calibration 38
- 7.3.1.1 Auto mode 39
- 7.3.1.2 Manual mode 40
- 7.4 pH calibration 41
- 7.4.1 One point calibration 41
- 7.4.1.1 Auto mode 41
- 7.4.1.2 Manual Mode 42
- 7.4.2 Two-point calibration 42
- 7.4.2.1 Auto Mode 42
- 7.4.2.2 Manual Mode 43
- 7.4.3 Process calibration 44
- (only for analog sensors) 46
- (only for analog sensor) 47
- 7.7 Sensor verication 47
- 8 Conguration 48
- 8.2.1.1 Analog sensor 49
- 8.2.1.2 ISM sensor 49
- 8.2.3.2 Concentration table 52
- 8.2.3.3 pH / ORP parameters 53
- or . key 54
- 8.2.4 Set averaging 55
- 8.3 Analog outputs 56
- 8.4 Set points 57
- 8.5 Alarm / Clean 58
- 8.5.1 Alarm 58
- 8.5.2 Clean 59
- 8.6 ISM set up 60
- 8.6.1 Sensor monitoring 60
- 8.6.2 CIP Cycle Limit 61
- 8.6.3 SIP Cycle Limit 62
- and . keys and press 63
- 8.7 Display 64
- 8.7.1 Measurement 64
- 8.7.2 Resolution 65
- 8.7.3 Backlight 65
- 8.7.4 Name 65
- 8.8 Hold analog outputs 66
- 9 System 67
- 9.2.1 Changing passwords 68
- 9.3 Set / Clear lockout 68
- 9.4 Reset 68
- 9.4.1 Reset system 69
- 9.5 Set date & time 69
- 10 PID setup 70
- 10.1 Enter PID setup 71
- 10.2 PID auto / manual 71
- 10.3 Mode 71
- 10.3.1 PID mode 72
- 10.4 Tune parameters 73
- 10.4.3 Proportional limits 73
- 10.4.4 Corner points 73
- 10.5 PID display 74
- 11 Service 75
- 11.1.3 Display 76
- 11.1.4 Keypad 76
- 11.1.5 Memory 76
- 11.1.6 Set OC 76
- 11.1.7 Read OC 77
- 11.1.8 Set analog outputs 77
- 11.1.9 Read analog outputs 77
- 11.2 Calibrate 77
- 11.2.1.1 Temperature 78
- 11.2.1.2 Current 78
- 11.2.1.3 Voltage 79
- 11.2.1.4 Rg diagnostic 79
- 11.2.1.5 Rr diagnostic 80
- 11.2.2 Calibrate unlock 81
- 11.3 Tech Service 81
- 12 Info 82
- 12.4 ISM sensor info 83
- 13 Maintenance 86
- 14 Troubleshooting 87
- 14.3.3 ORP messages 89
- 14.4 Amperometric O 90
- Error messages / 90
- Warning- and Alarm list 90
- 14.4.3 Trace oxygen sensors 91
- 14.5.1 Warning indication 92
- 14.5.2 Alarm indication 92
- 16 Specications 94
- 17 Default table 99
- Resistivity/Conductivity 103
- 18 Warranty 104
- 19 Buffer tables 105
- 19.1.2 Mettler-10 106
- 19.1.5 Hach buffers 107
- 19.1.6 Ciba (94) buffers 108
- 19.1.8 WTW buffers 109
- 19.1.9 JIS Z 8802 buffers 109
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M400/2(X)H
(131 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais