Mettler Toledo M300 ISM Especificações Página 65
- Página / 122
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter M300 65
© 12 / 11 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M300
Printed in Switzerland 52 121 389
8.5 Alarm/Clean
(PATH: Menu/Configure/Alarm/Clean)
Enter configuration mode as described in Section 8.1 ”Enter Configuration Mode”.
This Menu allows the configuration of Alarm and Clean functionality.
8.5.1 Alarm
To select ”Setup Alarm”, press the m or . key so that ”Alarm” is flashing.
Using the b and c buttons, navigate to ”Use Relay #”. Using the m or . keys, select a relay
to be used for the Alarm and press [ENTER].
One of the following events may be alarmed:
1. Power Failure
2. Software Failure
3. Rg Diagnostics – pH glass membrane resistance (pH sensors only; pH/pNa Rg diagnostics
detect both pH and pNa membrane glasses)
4. Rr Diagnostics – pH reference resistance (pH sensors only; except pH/pNa)
5. Cond cell open (cond sensors only)
6. Cond cell shorted (cond sensors only)
7. Channel A disconnected (ISM sensors only)
8. Channel B disconnected (only for ISM sensors and dual channel version)
If any of these criterias are set to Yes and the conditions for an alarm are given, the flashing
symbol a will be shown in the display, an alarm message will be recorded (see also chapter
12.1 ”Messages”; PATH: Info/Messages) and the selected relay will be activated. Furthermore an
alarm can be indicated by the current output if this has been parameterized (see chapter 8.3
”Analog Outputs”; PATH: Menu/Configure/Analog Outputs)
1. there is a power failure or power cycling
2. the software watchdog performs a reset
3. Rg is out of tolerance – for example, broken measuring electrode (pH only; pH/pNa Rg diag-
nostics detect both pH and pNa membrane glasses)
4. Rr is out of tolerance – for example, coated or depleted reference electrode (pH only)
5. If the conductivity sensor is on air (for example in an empty pipe)
6. If the conductivity sensor has a short cut
7. If no sensor is connected on channel A (ISM sensors only)
8. If no sensor is connected on channel B (only for ISM sensors and dual channel version)
For 1 and 2 the alarm indicator will be turned off when the alarm message is cleared. It will re-
appear if the power is constantly cycling or if the watchdog is repeatedly resetting the system.
OnlyforpHsensors
For 3 and 4 the alarm indicator will go off if the message is cleared and the sensor has been re-
placed or repaired so that the Rg and Rr values are within specification. If the Rg or Rr message
is cleared and Rg or Rr is still out of tolerance then the alarm will stay on and the message will
reappear. The Rg and Rr alarm can be turned off by going into this menu and setting Rg Diag-
nostics and/or Rr Diagnostics to No. The message can then be cleared and the alarm indicator
will be off even though Rg or Rr is out of tolerance.
- OperationManual 1
- TransmitterM300 1
- Transmitter M300 2 2
- Transmitter M300 4 4
- Transmitter M300 5 5
- Transmitter M300 6 6
- Transmitter M300 7 7
- Transmitter M300 8 8
- 1 Introduction 9
- 2 Safetyinstructions 10
- Transmitter M300 11 11
- 3 Unitoverview 12
- 3.3 Control/NavigationKeys 13
- 3.3.1 MenuStructure 13
- 3.3.2 Navigationkeys 13
- Transmitter M300 14 14
- 3.3.6 ”Savechanges”dialog 15
- 3.3.7 SecurityPasswords 15
- 3.4 Display 15
- 4 Installationinstruction 16
- Transmitter M300 17 17
- 1/2DINmodels 18
- Transmitter M300 19 19
- 40 ... 60 mm 20
- 1.57... 2.36" 20
- Transmitter M300 22 22
- 2: Terminal for sensors 23
- 4.3 ConnectorPINdenition 24
- ConductivitySensors 24
- (except58037221) 25
- Transmitter M300 26 26
- A B C D E F S 27
- 4.4.2 VPCableAssignment 28
- 4.4.3.1 Example1 29
- 4.4.3.2 Example2 30
- 4.4.4 Example3 31
- 4.4.4.1 Example4 32
- (except58037221) 33
- InPro 3250i/SG/120 35
- Art.-Nr. 52 005 373 35
- 4.7.2 AK9CableAssignment 36
- (ThorntonModelsonly) 36
- Transmitter M300 37 37
- 6 QuickSetup 38
- 7 SensorCalibration 39
- Transmitter M300 40 40
- (4-electrodesensorsonly) 41
- 7.2.3 ProcessCalibration 42
- 7.3 OxygenCalibration 43
- 7.3.1.1 Automode 43
- 7.3.1.2 Manualmode 44
- 7.3.2 ProcessCalibration 44
- 7.5 pHCalibration 45
- 7.5.1 OnePointCalibration 45
- 7.5.1.1 AutoMode 46
- 7.5.1.2 ManualMode 46
- 7.5.2 TwoPointCalibration 46
- 7.5.2.1 AutoMode 47
- 7.5.2.2 ManualMode 47
- 7.5.3 ProcessCalibration 48
- (notonISMVersion) 49
- (notonISMversion) 50
- 7.8 SensorVerication 51
- 8 Conguration 52
- Transmitter M300 53 53
- 8.2.2.3 CalculatedCO 55
- Transmitter M300 56 56
- Transmitter M300 57 57
- 8.2.4.2 pH/ORPParameters 58
- Transmitter M300 59 59
- 8.2.5 SetAveraging 60
- 8.3 AnalogOutputs 60
- Transmitter M300 61 61
- 8.4 Setpoints 62
- Transmitter M300 63 63
- Transmitter M300 64 64
- 8.5 Alarm/Clean 65
- 8.5.1 Alarm 65
- 8.6 Display 66
- 8.5.2 Clean 66
- 8.6.1 Measurement 67
- 8.6.2 Resolution 67
- 8.6.3 Backlight 67
- 8.6.4 Name 68
- 8.7 HoldAnalogOutputs 68
- 9 System 69
- 9.3 Passwords 70
- 9.3.1 ChangingPasswords 70
- 9.4 Set/ClearLockout 70
- 9.5 Reset 71
- 9.5.1 ResetSystem 71
- Settings 72
- 10 PIDSetup 73
- 10.1 EnterPIDSetup 74
- 10.2 PIDAuto/Manual 75
- 10.3 Mode 75
- 10.3.1 PIDMode 75
- 10.4 TuneParameters 76
- 10.4.3 ProportionalLimits 77
- 10.4.4 CornerPoints 77
- 10.5 PIDDisplay 77
- 11 Service 78
- 11.2.2 DigitalInput 79
- 11.2.3 Display 79
- 11.2.4 Keypad 79
- 11.2.5 Memory 79
- 11.2.6 SetRelay 80
- 11.2.7 ReadRelays 80
- 11.2.8 SetAnalogOutputs 80
- 11.2.9 ReadAnalogOutputs 80
- 11.3 Calibrate 81
- 11.3.1.1 Resistance 81
- 11.3.1.2 Temperature 82
- 11.3.1.3 Current 83
- 11.3.1.4 Voltage 83
- 11.3.1.5 RgDiagnostic 84
- 11.3.1.6 RrDiagnostics 84
- 11.3.2 CalibrateAnalog 85
- 11.3.3 CalibrateUnlock 85
- 11.4 TechService 85
- 12 Info 86
- 12.4 Model/SoftwareRevision 87
- 13 Maintenance 88
- 14 Troubleshooting 89
- Transmitter M300 90 90
- 14.2.3 ORPmessages 91
- (ThorntonModelsonly) 92
- Transmitter M300 93 93
- 14.8.2 Alarmindication 94
- Transmitter M300 95 95
- 16 Specications 96
- Transmitter M300 97 97
- 1/2DINand1/4DINversions 98
- 17 Defaulttables 100
- Transmitter M300 101 101
- Resitivity 102
- Transmitter M300 103 103
- 17.4 M300O 105
- (Single-ChannelInstruments) 105
- Transmitter M300 106 106
- Transmitter M300 107 107
- Transmitter M300 108 108
- Transmitter M300 109 109
- Transmitter M300 110 110
- Transmitter M300 111 111
- ThorntonModelsonly) 112
- Transmitter M300 113 113
- 18 Warranty 114
- 19 Certicate 115
- 20 Buffertables 116
- 20.1.2 Mettler-10 117
- 20.1.5 Hachbuffers 118
- 20.1.6 Ciba(94)buffers 119
- 20.1.8 WTWbuffers 120
- 20.1.9 JISZ8802buffers 120
- Transmitter M300 121 121
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M300 ISM
(111 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.173 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais