Mettler Toledo M300 ISM Especificações Página 55
- Página / 122
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Transmitter M300 55
© 12 / 11 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M300
Printed in Switzerland 52 121 389
8.2.2.3 CalculatedCO
2
(Powerplantapplicationsonly)
Carbon dioxidemay be calculated from cation conductivity and degassed cation conductivity
measurements on power plant samples using tables from ASTM Standard D4519. The M300
has these tables stored in memory, which it uses when units of CO
2
CAL are selected.
The calculated CO
2
measurement must be configured to the same channel as cation conductivi-
ty. For example, set up measurement ”a” on channel A to be cation conductivity, measurement
”b” on channel B to be degassed cation conductivity, measurement ”c” on
channel A to be calculated CO
2
and measurement ”d” on channel B to be temperature.
Set the temperature compensation mode to ”Cation” for both conductivity measurements.
8.2.3 TemperatureSource(notonISMversion)
(PATH: Menu/Configure/Measurement/Temperature Source)
Enter Configuration Mode as described in section 8.1 ”Enter Configuration mode” and select the
menu Measurement (see section 8.2 ”Configuration/Measurement”).
Navigate to the menu Temperature Source by using the m or . key. Press the [ENTER] key to
select this Menu. The following options can be chosen:
”Fixed”: allows a specific temperature value to be entered.
h
NOTE:The selection depends on the transmitter type. For detailed overview see the specifications
in section 16 ”Specification”.
”Use this Ch Pt1000”: temperature input will be taken from the sensor attached.
”Use this Ch Pt100”: temperature input will be taken from sensor attached
”Use this NTC22K”: temperature will be taken from the sensor attached
”Fixed = 25°C”: allows a specific temperature value to be entered
”Use Other Channel”: temperature input will be taken from the sensor attached to the other
channel (only on dual channel version)
h
NOTE: If temperature source is set to Fixed, the temperature applied during one-point and/or two-
point calibration of pH electrodes can be adjusted within the corresponding calibration proce-
dure. After the calibration the fixed temperature defined in this configuration menu is valid again.
Pressing the [ENTER] key will bring up the Save Changes dialog.
Selecting No will discard the entered values and return to the measurement display screen, se-
lecting Yes will save changes made.
- OperationManual 1
- TransmitterM300 1
- Transmitter M300 2 2
- Transmitter M300 4 4
- Transmitter M300 5 5
- Transmitter M300 6 6
- Transmitter M300 7 7
- Transmitter M300 8 8
- 1 Introduction 9
- 2 Safetyinstructions 10
- Transmitter M300 11 11
- 3 Unitoverview 12
- 3.3 Control/NavigationKeys 13
- 3.3.1 MenuStructure 13
- 3.3.2 Navigationkeys 13
- Transmitter M300 14 14
- 3.3.6 ”Savechanges”dialog 15
- 3.3.7 SecurityPasswords 15
- 3.4 Display 15
- 4 Installationinstruction 16
- Transmitter M300 17 17
- 1/2DINmodels 18
- Transmitter M300 19 19
- 40 ... 60 mm 20
- 1.57... 2.36" 20
- Transmitter M300 22 22
- 2: Terminal for sensors 23
- 4.3 ConnectorPINdenition 24
- ConductivitySensors 24
- (except58037221) 25
- Transmitter M300 26 26
- A B C D E F S 27
- 4.4.2 VPCableAssignment 28
- 4.4.3.1 Example1 29
- 4.4.3.2 Example2 30
- 4.4.4 Example3 31
- 4.4.4.1 Example4 32
- (except58037221) 33
- InPro 3250i/SG/120 35
- Art.-Nr. 52 005 373 35
- 4.7.2 AK9CableAssignment 36
- (ThorntonModelsonly) 36
- Transmitter M300 37 37
- 6 QuickSetup 38
- 7 SensorCalibration 39
- Transmitter M300 40 40
- (4-electrodesensorsonly) 41
- 7.2.3 ProcessCalibration 42
- 7.3 OxygenCalibration 43
- 7.3.1.1 Automode 43
- 7.3.1.2 Manualmode 44
- 7.3.2 ProcessCalibration 44
- 7.5 pHCalibration 45
- 7.5.1 OnePointCalibration 45
- 7.5.1.1 AutoMode 46
- 7.5.1.2 ManualMode 46
- 7.5.2 TwoPointCalibration 46
- 7.5.2.1 AutoMode 47
- 7.5.2.2 ManualMode 47
- 7.5.3 ProcessCalibration 48
- (notonISMVersion) 49
- (notonISMversion) 50
- 7.8 SensorVerication 51
- 8 Conguration 52
- Transmitter M300 53 53
- 8.2.2.3 CalculatedCO 55
- Transmitter M300 56 56
- Transmitter M300 57 57
- 8.2.4.2 pH/ORPParameters 58
- Transmitter M300 59 59
- 8.2.5 SetAveraging 60
- 8.3 AnalogOutputs 60
- Transmitter M300 61 61
- 8.4 Setpoints 62
- Transmitter M300 63 63
- Transmitter M300 64 64
- 8.5 Alarm/Clean 65
- 8.5.1 Alarm 65
- 8.6 Display 66
- 8.5.2 Clean 66
- 8.6.1 Measurement 67
- 8.6.2 Resolution 67
- 8.6.3 Backlight 67
- 8.6.4 Name 68
- 8.7 HoldAnalogOutputs 68
- 9 System 69
- 9.3 Passwords 70
- 9.3.1 ChangingPasswords 70
- 9.4 Set/ClearLockout 70
- 9.5 Reset 71
- 9.5.1 ResetSystem 71
- Settings 72
- 10 PIDSetup 73
- 10.1 EnterPIDSetup 74
- 10.2 PIDAuto/Manual 75
- 10.3 Mode 75
- 10.3.1 PIDMode 75
- 10.4 TuneParameters 76
- 10.4.3 ProportionalLimits 77
- 10.4.4 CornerPoints 77
- 10.5 PIDDisplay 77
- 11 Service 78
- 11.2.2 DigitalInput 79
- 11.2.3 Display 79
- 11.2.4 Keypad 79
- 11.2.5 Memory 79
- 11.2.6 SetRelay 80
- 11.2.7 ReadRelays 80
- 11.2.8 SetAnalogOutputs 80
- 11.2.9 ReadAnalogOutputs 80
- 11.3 Calibrate 81
- 11.3.1.1 Resistance 81
- 11.3.1.2 Temperature 82
- 11.3.1.3 Current 83
- 11.3.1.4 Voltage 83
- 11.3.1.5 RgDiagnostic 84
- 11.3.1.6 RrDiagnostics 84
- 11.3.2 CalibrateAnalog 85
- 11.3.3 CalibrateUnlock 85
- 11.4 TechService 85
- 12 Info 86
- 12.4 Model/SoftwareRevision 87
- 13 Maintenance 88
- 14 Troubleshooting 89
- Transmitter M300 90 90
- 14.2.3 ORPmessages 91
- (ThorntonModelsonly) 92
- Transmitter M300 93 93
- 14.8.2 Alarmindication 94
- Transmitter M300 95 95
- 16 Specications 96
- Transmitter M300 97 97
- 1/2DINand1/4DINversions 98
- 17 Defaulttables 100
- Transmitter M300 101 101
- Resitivity 102
- Transmitter M300 103 103
- 17.4 M300O 105
- (Single-ChannelInstruments) 105
- Transmitter M300 106 106
- Transmitter M300 107 107
- Transmitter M300 108 108
- Transmitter M300 109 109
- Transmitter M300 110 110
- Transmitter M300 111 111
- ThorntonModelsonly) 112
- Transmitter M300 113 113
- 18 Warranty 114
- 19 Certicate 115
- 20 Buffertables 116
- 20.1.2 Mettler-10 117
- 20.1.5 Hachbuffers 118
- 20.1.6 Ciba(94)buffers 119
- 20.1.8 WTWbuffers 120
- 20.1.9 JISZ8802buffers 120
- Transmitter M300 121 121
Manuais e produtos relacionados com Medição, teste e controlo Mettler Toledo M300 ISM
(111 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais